Analysis of the causes of the flashing of injection molded products and solutions. The flash edge, also known as overflow, blunt, burr, etc., mostly occurs at the position of the mold, such as the parting surface of the movable mold and the static mold, and the sliding part of the slider. , the gap of the insert, the hole of the ejector pin, etc., the flash edge is largely caused by the failure of the mold or machine clamping force. The details may be caused by the following reasons:
1. The highest clamping force of the machine should be enough to use the machine with sufficient clamping force. The clamping machine wears or the clamping cylinder seal element wears and drops or recirculates, causing the clamping force to decrease. If the heating system is out of control and the actual temperature is too high, check whether there are any problems with the thermocouple or heating coil.
2. (1) If the mold cavity is unbalanced or the parallelism is insufficient, the partial force is caused by the unbalanced force, and the local burrs are partially dissatisfied. The flow channel should be placed in the center of mass symmetry as much as possible without affecting the integrity of the workpiece.
(2) When the movable member and the sliding core in the mold are unbalanced, they will cause flash.
(3) When the mold is exhausted, the compressed air will expand the parting surface of the mold and cause flashing. A good exhaust system should be opened, or the exhaust groove should be dug on the parting surface.
3. If the fluidity of the plastic is too large, or if too much lubricant is added, the pressure, speed, temperature, etc. should be appropriately reduced, the amount of lubricant used should be reduced, and if necessary, a plastic with low fluidity should be selected.
4. Processing and adjustment:
(1) If the set temperature, pressure and speed are too high, segmental injection should be used. Excessive injection time, dwell time, and too much feed will cause flash.
(2) When adjusting, the hinge of the clamping machine is not straightened, or the mold nut is often moved when the mold is opened or locked, and the clamping force is insufficient to cause flashing.
(3) The parallelism of the adjustment head and the two poles is insufficient or the system pressure of the adjustment is too large.
5. Reasons for repeated occurrences of flashing and manufacturing dissatisfaction:
(1) When the particle size of the plastic raw material is unevenly distributed, the amount of the added material may be indefinite.
(2) The wear of the rubber head, the rubber ring and the rubber gasket of the screw is too large, so that the melt may slide or return between the screw and the cylinder to cause flash or dissatisfaction.
(3) The cooling system of the inflow port is invalid, so that the feed is adjusted.
(4) The amount of shots set by the barrel is insufficient, that is, if the cushion is too small, there will be a lot of burrs or dissatisfaction of the parts.
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Office Partition Aluminium Profiles
So why is aluminum profile popular? Why do you choose aluminum profile to customize this office partition?
Firstly, because the hardness of aluminum profile is relatively high, it is not easy to deform, and the landing is relatively stable, the surface of aluminum profile is anodized with a thickness of 12 microns to form a tenacious oxide film. The surface is very beautiful, and the anti-corrosion performance is relatively good. The partition of the office is customized with aluminum profile. The connection mode adopted is the connection of accessories, that is, special aluminum profile accessories. There is no need for installation, seamless connection, and disassembly and installation are very convenient; Aluminum profile has smooth surface, simple maintenance, long service life and can be recycled; The cost performance of aluminum profile office partition is very high, which is better than stainless steel and ordinary steel.Office Partition and door,Office Wall,Fireproof Aluminum Office Partition Profile,Top Industrial Office Wall.
Office Partition Aluminium Profiles,Office Partition And Door,Top Industrial Office Wall,Office Partition Walls With Doors
GuangDong XinCheng Material CO.,LTD , https://www.xin-alu.com